If for any reason you are not satisfied with your gear in the first 30 days – enjoy no hassle returns. This applies only to new products purchased directly from goalzero.com. All products are covered from defects under normal use for up to two years. For more information, visit Warranty & Returns in our Support center.

0
10 Amp Charge Controller
10 Amp Charge Controller
10 Amp Charge Controller
SKU: 96100
10 Amp Charge Controller
$69.95

Monitor and regulate solar input for 12V batteries with the 10 Amp Charge Controller. Designed to integrate seamlessly with Goal Zero solar panels, the charge controller comes with a pre-installed 8mm solar connector and an easy-to-read LED screen. Equipped with an IP65 rating, the charge controller is weather resistant and dustproof, allowing for protection against the elements when powering off-grid adventures or outdoor equipment.
... more
California residents:WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov

Charging & Power

Tech Specs

Q&A

Reviews

In The Box

Charging & Power

10 Amp Charge Controller

Designed to monitor and regulate solar input for 12V batteries. For solar charging with 100 watts and below, we recommend the 10 Amp Charge Controller. For solar charging with more than 100 watts, we recommend the [20 Amp Charge Controller](https://www.goalzero.com/shop/accessories/20a-charge-controller/)

Designed to monitor and regulate solar input for 12V batteries. For solar charging with 100 watts and below, we recommend the 10 Amp Charge Controller. For solar charging with more than 100 watts, we recommend the 20 Amp Charge Controller

Charge Controller comes with an integrated 8mm Goal Zero solar connector. To connect and charge a 12V battery, you must purchase the [Spade to SAE Cable](https://www.goalzero.com/shop/accessories/spade-sae-cable/) and additional cable adaptors. We recommend either the [SAE to Ring Terminal](https://www.goalzero.com/shop/accessories/sae-ring-terminal/) or [SAE to Alligator Clip](https://www.goalzero.com/shop/accessories/sae-alligator-clip/)

Charge Controller comes with an integrated 8mm Goal Zero solar connector. To connect and charge a 12V battery, you must purchase the Spade to SAE Cable and additional cable adaptors. We recommend either the SAE to Ring Terminal or SAE to Alligator Clip

Will not work with Yeti X Power Supply

Will not work with Yeti X Power Supply

10 Amp Charge Controller
Tech Specs
Ports
  • Input/Output terminal: M5 terminals
  • Input Port: Solar Port: (blue, 8mm): 14-22.5V up to 10A
  • Fuse: 15A replaceable
Battery Details
  • Charge Controller: PWM
  • Rated solar panel amps GZ-10: 10A
  • Normal input solar cell array voltage: 15-22V
  • Max solar cell array voltage (output has no load): 25V
  • Lowest operating voltage at solar or battery side: 8V Minimum
  • Charging Characteristics:
  • Start Voltage at 25°C: 3-10V
  • Charge Voltage at 25°C:
  • LTO battery: 14.0V
  • Gel battery: 14.1V
  • LiFePO4 battery: 14.4V
  • Charge Voltage at 25°C: AGM battery-14.4V
  • WET battery: 14.7V
  • Calcium battery: 14.9V
  • Equalizing Voltage at 25°C: WET or Calcium battery-15.5V
  • Float Voltage at 25°C:
  • Gel, AGM, WET, Calcium batteries-13.6V
  • LTO and LiFePO4 batteries-13.4V
  • Battery temperature compensation coefficient: -24mV/°C
General
  • Product SKU: 96100
  • Weight: 14.4oz (408g)
  • Dimensions: 6.10 x 3.90 x 1.02in (15.5 x 9.91 x 2.6cm)
  • IP Grade: IP65
  • Spade to 8mm Cable Length: 3ft
  • Operating temperature: -25 to 50°C/ -13 to 122°F
  • Warranty: 12 Months
  • Certs: IC, FCC, CE-EMC, CE-LVD
Q&A
Reviews
In The Box

What's in the Box

  • 10A Charge Controller
  • Spade to 8mm Cable
What's in the Box

Compatibility

Compatible with the Nomad 50, Nomad 100, Boulder 50, Boulder 100, and Boulder 100 Briefcase. Charge controller can be installed directly on a Boulder 50, Boulder 100, Boulder 100 Briefcase with available Boulder Charge Controller Mounting Brackets
Still have questions? Give us a call.
top